The brand

UV disinfection for
water and process duty.

Aquafine builds UV disinfection and treatment systems used across water and process applications. Green Marine specifies the range where the installation calls for higher-flow chambers or process-water-specific configurations.

Lamps, sleeves and sensors are held for the systems we support, and every service visit is closed with a written record of the dose state and the intensity readings.

  • System supply and sizing
  • Lamp and quartz sleeve replacement
  • Sleeve cleaning and inspection
  • Intensity sensor checks
  • Controller and alarm verification
  • Consumable resupply
Schematic of an Aquafine UV chamber with intensity monitoring.
UV chamber, intensity monitoring and interlocks.View full size

What Green Marine supplies

The range,
and what keeps it running.

Complete Aquafine systems and the parts, elements or consumables they need after they are aboard.

Complete UV systems

UV chambers sized for higher-flow and process water duties.

Replacement lamps

UV lamps matched to the chamber and dose target of the installed system.

Quartz sleeves & seals

Sleeves, gaskets and seals for the chambers we service.

Sensors & controls

Intensity sensors, controllers, alarms and the interlock components that make treatment verifiable.

Applications

Where these systems
run on the Gulf.

The Aquafine range Green Marine specifies most often across commercial, offshore and government installations.

01

Process water treatment

UV disinfection on process and service water loops where quality has to be verifiable.

02

Higher-flow potable water

Larger chambers for accommodation and process potable water lines.

03

Treated effluent polishing

Downstream of a treatment plant to polish the discharge.

04

Newbuild and retrofit

Shipyard supply and commissioning, plus retrofit into existing treatment lineups.

Why buy it from Green Marine

The manufacturer
relationship, on the Gulf Coast.

A direct relationship with Aquafine means parts, documentation and technical answers come from the source rather than a guess. Green Marine specifies the range, holds the parts most commonly needed on the vessels we support, and stands behind every install.

Every service visit is documented, so the next person to open the equipment knows what was found and what was done.

  • Authorised distributor and service partner
  • Direct manufacturer relationship
  • Manuals, parts breakdowns and service bulletins
  • Technical escalation route for engineering questions
  • Gulf Coast stock of common wear parts
  • Written service reports on every visit
  • Commissioning support for shipyard projects
Diagram of the Green Marine field service cycle: dispatch, mobilise, diagnose, repair, verify, report, follow up.
How a service call runs, start to finish.View full size

How to start

From nameplate
to a written quote.

Green Marine works from whatever information you have aboard. The four steps below are the same whether it is a spec-out for a newbuild or a replacement part for a running unit.

  1. 01

    Tell us the vessel

    Vessel name or hull, the system aboard, and whether it is a supply, replacement or service enquiry.

  2. 02

    Send what you have

    Make, model, serial number, part number — or a photo of the nameplate. Whatever you have is enough to start.

  3. 03

    We spec and price

    Written quote against the correct build and revision, with lead times and any commissioning or install support quoted separately.

  4. 04

    Delivered and documented

    Parts shipped where you need them, or the field team booked. Every visit closes with a written service report.

Start here

Request a
quote.

Every quote is answered by an engineer, not a form email. Send the vessel, the system and anything you have on the nameplate — that is enough to price against.

Field service, spare parts and commissioning can all be quoted from the same request.

  • Sized and priced against the actual unit aboard
  • Written response with lead time and options
  • Direct manufacturer support if engineering input is needed

Prefer to talk? Direct dial and email addresses are on the contact page.

About you
The vessel and system

Leave blank if the timing is flexible.

The problem or requirement

Written service reports and existing installation notes are welcome as attachments below.

Nameplate photos, part diagrams, existing service reports. Up to 8 files, 25 MB total.

Fields marked * are required.

Next step

Have a nameplate
but no model?

Send us a photo of the plate and the vessel it is on. We identify the correct build, revision and part number from there.